Friday 24 February 2012

Homemade Warping Frame

The completed warping frame with its first warp
We got our loom just before Christmas 2010; it is a Harrisville 36” loom with 8 shafts and 10 treadles. It belonged to someone who had come over from the states and then had to return, unable to take it back with them. Having cluttered up the bedroom of their friend for some time we saw an advert asking if anyone wanted it before it went to the dump... We jumped at the chance and have been the proud owners since. I cannot imagine that there are many Harrisville Looms in England as there is no distributor for them here.

That first Christmas we learnt to use it by weaving three scarves and two ties, which were given away as presents. These were made with a weaving book in one hand and the beater in the other, with the last one only being cut off and fulled late into the night before we set off to be with family. 

The frame is oak and
the pegs hazel
Given that we didn’t really allow ourselves much time to learn the process of weaving they came out quite well. However, one area where we did struggle was with the tension as we didn’t have a warping frame and so was using various Heath Robinson style contraptions involving chairs and sofas etc., none of which really worked satisfactorily.

I briefly looked at the Ashford warping frame, but at £75 ($120) pretty quickly dismissed it – not only on cost, but also because it was made in New Zealand and shipped over. I am sure that it is very nicely made, but it is only four bars with pegs coming out and so I set to making one. It has been an on/off project all through last year, but finally it is finished and we can return to weaving, as we haven’t touched it since the last scarf came off the loom that Christmas.

How to make a warping frame

Full plans for the warping frame can be download in .pdf by clicking here.

The frame has mortise and
tenon joints, secured with
copper pins

I used 20mm (¾”) oak for the actual frame as I have a pile of solid oak floorboards, but you could use any easy to work straight grain timber. I guess you could even use softwood as it isn’t under much load. The width of the frame timber is 45mm (1 ¾”).
The uprights are cut to 80cm (31 ½”) in length and 25mm (1”) long tenons are cut at the end, at a width of 6mm (1/4”). The horizontal members are 103cm (40 ½”) as this allows the spacing from peg to peg to be around 1m (39 ½”), which makes for an easy rough and ready warp length calculation. If you are more comfortable with imperial measurements you could always adjust it to make them a yard apart. I then cut the mortises in the horizontal members.

It is easier to drill the holes for the pegs before you assemble the frame, although I put them in at the end. For my pegs I used hazel; it is a local wood that grows in coppices and hence the rods are reasonably straight. It isn’t a particularly strong wood, but by simply debarking it and using it ‘in the round’ I am retaining the strength of the grain. It is quite important that the pegs are straight as a significant variation throughout the length of the peg will be reflected in the warp. However, it does only really need to be straight on one side (i.e. the outer one around which the warp turns). Quite whether these hazel pegs are straight enough I am not sure – I guess time will tell – if not I will replace them with oak dowel. The pegs are 16.5cm (6 ½”) long and around 12mm (1/2”) in diameter (in actual fact the diameter of the pegs are quite varied being hazel rods – which I love – but dowel would obviously give a consistent finish). Drill the hole slightly smaller than the pegs.

It is important that the pegs be square to the frame
On the left upright the centre of the top hole is 16.5cm (6 ½”) from the tenon shoulder, with the centre of the holes below being at 14cm (5 ½”) intervals. For the right upright the centre of the first hole is 3cm (1 ¼”) and then again they are every 14cm (5 ½”). All the holes are in the centre of the wood and each side has 5 pegs.

The upper horizontal member has the centre of the first hole 10cm (4”) in from the left handside, then two more, both at 20cm (8”) intervals. The lower member is the same, except you measure from the right hand edge. 

Assemble the frame and either glue the tenons or, as I did, peg them. Given that these were my first mortice and tenon joints I wasn’t about to risk drawboring with wooden pegs (I’ll save that for another day), but at the same time I am not keen on glue. So instead I pinned them with copper tacks, two in each tenon, straight through the side of the mortise – which has worked really well.

Download a .pdf version of the plan by clicking here
Once the frame is together it is just a matter of fitting the pegs with a wooden mallet, gently trimming the end and then tapping them home. Be careful that you don’t make it too tight and split the member, but tight enough so that they won’t fall out (no glue should be needed). Likewise stop and check them every so often with a set square to see that they are going in straight.

Finally screw in four brass hooks so that the frame can be mounted on the wall.

And there we are, another tool handmade – saving me money, teaching me new skills and reducing my impact on the environment. I dare say the Ashford one is a little more ‘polished’, but I rather like the natural look of ours. Right, time to get going on our first warp...

6 comments:

  1. Please comment more about the "flat side" of the pegs in you statement as follows: "However, it does only really need to be flat on one side (i.e. the outer one around which the warp turns)."
    Should I actually file one side of the peg flat?

    ReplyDelete
    Replies
    1. Sorry, flat is not the correct word - I will change it. I mean straight. As the wool only passes on the outside, this need to be a) at 90 degrees to the frame and b) without any knots, bumps or hollows. However, the inside face can be as knotted and curved as you like.

      Obviously all this is just make sure that all the threads are the same length.

      In reality if you use dowel you will have none of these problems, so long as you get them in straight to the frame.

      I hope this helps.

      Delete
  2. How did you figure out what dimensions to use for the overall size Ovid the frame, and how far apart the dowels should be? I just bought a used four harness table loom but I am a total novice when it comes to warping so I need to figure out what dimensions top make my warping board! Thanks! :)

    ReplyDelete
  3. Thank you for posting these instructions. Hope to make one soon.

    ReplyDelete
  4. What is the max yardage of warp that this board will measure out? Thank you.

    ReplyDelete
  5. thanks for the instructions!

    ReplyDelete